Freshtel SPA-2000 Manual do Utilizador descarregar pdf (Página 1)

Sipura SPA-2000

Manual Configuration Instructions

Only settings that deviate from factory defaults are included in this document. If your ATA

was previously connected to a different service, you will need to use the screenshots to verify

that all settings are correct; alternatively, you may reset the ATA to factory defaults

(recommended), as described in section 4.

1. Plug in the ATA

Connect a telephone handset, network, and power to the ATA, and wait briefly while it

discovers its IP address via DHCP. For more information on connecting your ATA, or to set a

Static IP Address manually, please consult your User Manual.

2. Determine the ATA’s IP Address

To find out the ATA's IP Address, dial "****", then "110#". Note down the IP Address spoken

out and enter it into the address bar of a Web browser.

Example: If the address is "10.34.238.6", enter this as "http://10.24.238.6/".

If the address read out is "0.0.0.0", the ATA was unsuccessful in acquiring an IP address via

DHCP -- contact your network administrator before proceeding.

3. Reset the ATA to Factory Defaults (optional).

Note: This will clear all custom settings from the ATA; if you wish to retain these for later

reference, please make a note of them (for example, by printing the configuration pages, or

saving a copy of them to disk).

To perform the reset, dial "****" on the attached telephone handset, followed by "73738#",

then "1" to confirm; then hang up. Once the phone is hung up, the ATA will restart with its

settings reset to factory defaults.

1 2 3 4 5 6 7 8

Resumo do Conteúdo

Página 1 - Sipura SPA-2000

Sipura SPA-2000 Manual Configuration Instructions Only settings that deviate from factory defaults are included in this document. If your ATA

Página 2

4. Configure the ATA via its web interface Bring up the ATA's Web configuration page, as described in section 2 of this document. Click on

Página 3

SIP NAT Support Parameters Handle VIA received: yes Handle VIA rport: yes Insert VIA received: yes Insert VIA r

Página 4

Distinctive Ring Patterns Ring 1 Cadence: 60(1.5/3.4) Ring 3 Cadence: 60(1.5/3.4,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/2,.4/.2,.4/

Página 5

Regional (all countries) Miscellaneous Time Zone: GMT+10:00 <or as appropriate> FXS Port Impedance: 600 &

Página 6

Line 1 (and 2, if using a different Firefly number on the second line) NAT Mapping Enable: yes NAT Keep Alive Enable: yes N

Página 7

Audio Configuration Preferred Codec: G729a NOTE: It is vital that the dial plans are entered correctly – as there is not enough space

Página 8 - Freshtel website

Dial Plan (UK only -- user has local dialing prefix set) (*123|*xxxxxxxx|999 S0|112 S0|18000 S0|18001999 S0|0800112999 S0|[2-9]xxxxxxx|[2-9]xxxx

Comentários a estes Manuais

Sem comentários

Lg D2242P-PN Manuel de l'utilisateur (25 pages)

marque: Lg | Catégorie: TVs & monitors | Taille: 4.23 MB |

Table des matières

CINEMA 3D MONITOR

CONTENTS

ASSEMBLING AND PREPARING

Parts and buttons

Setting up the Monitor set

Mounting on a table

Mounting on a wall

USING THE MONITOR SET

NOTE NOTE

MONITOR SETUP

MENU AUTO VOLUME INPUT EXIT

Customizing Settings

3D Settings(Only 3D mode)

SUPER ENERGY SAVING Settings

TROUBLESHOOTING

SPECIFICATIONS

Preset Modes (Resolution)

HDMI 3D TIMING

Indicator

SAFETY PRECAUTIONS

PROPER POSTURE